{"product_id":"sonax-profiline-schaumpad-hart-polierpad","title":"PROFILINE Foam Pad hard polishing pad","description":"\u003ch2\u003eMaximum cut on weathered paint — SONAX PROFILINE Foam Pad hard\u003c\/h2\u003e\n\n\u003cblockquote\u003e\n  \u003cp\u003e\u003cem\u003eWhat is a hard polishing pad used for in a pro setting? A hard polishing pad like the \u003cstrong\u003eSONAX PROFILINE Foam Pad hard\u003c\/strong\u003e maxes out the cut of whatever polish you run on it — it takes off more clear coat than softer pads, which makes it the right tool for deeply weathered clear coat, heavy holograms and oxidised surfaces.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003cp\u003eIn paint correction the pairing of polish and pad drives the result more than anything else: the same cutting polish gives you far less bite on a soft pad than on a hard one. If you want to pull heavy defects — deeply baked-in holograms, oxidation, deep scratches down into the clear coat — out of the paint efficiently, you need the right pad setup. That's exactly what the \u003cstrong\u003eSONAX PROFILINE Foam Pad hard\u003c\/strong\u003e was built for: a high-density, open-cell foam polishing pad that lets cutting polishes like PROFILINE CutMax work at full strength. Available in Ø75 mm and Ø150 mm for all common polishers.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMaximum cutting power thanks to high foam density and open-cell structure.\u003c\/strong\u003e The high foam density of the Foam Pad hard means the pad gives very little under load, so the polish stays pressed onto the paint with constant pressure. At the same time the open-cell structure lets the polish spread and release evenly across the whole working face. The result is a controllable, even cut — no local hot spots, no uneven removal.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLong service life thanks to centre cooling and good airflow.\u003c\/strong\u003e Hard cutting builds heat — a problem for cheap pads that warp or fall apart when things get hot. The Foam Pad hard has a dedicated centre-cooling core and an open airflow structure that stops heat from building up. That stretches the pad's service life a lot and lets you polish across several cars without wrecking the pad or burning sanding marks into the paint through overheating.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFast swaps and precise handling thanks to hook-and-loop backing and a bevelled edge.\u003c\/strong\u003e In day-to-day work every minute counts: the hook-and-loop backing on the Foam Pad hard lets you swap pads in seconds, no tools and no break in the flow. The bevelled foam edge improves handling on edges, corners and tight spots — a detail that, when you're working fenders, door edges and spoilers, makes the difference between a clean result and an unpolished strip along the edge.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003chr\u003e\n\n\u003cblockquote class=\"praxistipp\"\u003e\n  \u003cp\u003e\u003cstrong\u003eDetailing1's tip from the shop:\u003c\/strong\u003e With the Foam Pad hard, work panel by panel: only ever do one panel (bonnet, roof, a side) per pass, never the whole body at once. The pad releases the polish more evenly when it doesn't sit too long between wetting and wipe-off. After 2–3 panels, clean the pad with a soft pad brush or a quick blast of compressed air — that keeps caked-on polish residue off, which can drag micro-scratches back in as you keep going. When you're done: soak it for 30 minutes in warm water with PROFILINE Microfibre Wash, wring it out and lay it flat to air-dry.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003ch3\u003eFoam Pad hard technology — foam density, open cells and cutting behaviour\u003c\/h3\u003e\n\n\u003cp\u003eThe cutting power of a pad system comes from three factors working together: the hardness of the pad, the open-cell nature of the foam and the abrasive strength of the polish you run. The \u003cstrong\u003eFoam Pad hard\u003c\/strong\u003e is built for maximum pad intensity — it's the hardest foam pad in the PROFILINE range, which makes it the right pad for heavy-cut polishes like the \u003ca href=\"\/products\/sonax-profiline-cutmax-schleif-politur\"\u003eSONAX PROFILINE CutMax \"6\/4\" cutting polish\u003c\/a\u003e or the \u003ca href=\"\/products\/sonax-profiline-ultimatecut-schleif-politur\"\u003eSONAX PROFILINE UltimateCut \"6+\/3\"\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cp\u003eThe open-cell foam of the Foam Pad hard does two jobs: first, the open structure holds larger amounts of polish and releases it evenly and continuously across the working face — no flooding the paint, no dry patches. Second, open cells shed heat better than closed foams: heat generated while you polish is carried out through the pores instead of stored in the pad. Together with the dedicated cooling zone in the centre of the pad, you get a system that stays controllable even on longer polishing sessions and doesn't put the paint at risk through local overheating.\u003c\/p\u003e\n\n\u003cp\u003eOne thing that matters day-to-day: a hard pad ups the cut, but there are limits too. On freshly polished, thin clear coat, or on cars with a single-stage base coat and no clear, run the Foam Pad hard only with dialled-back machine settings. The pad itself gives you no feedback on how much clear coat is left — measuring paint thickness before you polish is a must, not an option, when you're cutting hard.\u003c\/p\u003e\n\n\u003ch3\u003eUsing the Foam Pad hard — polish combo, machine and technique\u003c\/h3\u003e\n\n\u003cp\u003eThe Foam Pad hard suits all common polishers: rotary polishers (rotaries), dual-action polishers and DA machines. The best machine choice depends on the job: for maximum cut on heavily weathered paint, go with a rotary and the Foam Pad hard, since rotaries remove more at the same rpm than dual-action machines. For steadier, safer work on the everyday holograms you see on new cars, a dual-action machine with the Foam Pad hard is a good compromise between cutting power and control.\u003c\/p\u003e\n\n\u003cp\u003eHow you spread the polish on the pad is decisive for the result. The go-to is the \"five-point pattern\": four small dabs of polish at the corners of the working face and one in the middle. Then, with the machine off, spread it briefly across the paint before you start it up — that stops the polish flinging off when you switch on. Machine speed for the Foam Pad hard should sit between 1,200 and 1,800 rpm depending on polish and paint hardness; very hard paints (Japanese cars) need higher speeds, softer paints (French and British makes) respond better to lower ones.\u003c\/p\u003e\n\n\u003cp\u003eAfter polishing: clean the polish residue off the pad straight away with a soft pad brush. Caked polish in the pad gives you an uneven cut next time and can leave grooves in the paint. If you work several pads at once, you can swap between panels and clean the resting pad in peace — your pace goes up, pad quality stays constant.\u003c\/p\u003e\n\n\u003ch3\u003eWhere the Foam Pad hard fits — weathered paint, oxidation and GRP surfaces\u003c\/h3\u003e\n\n\u003cp\u003eThe Foam Pad hard covers three main areas: heavily weathered car paint, oxidised surfaces and GRP (glass-reinforced plastic). Heavily weathered paint — typical on cars left exposed for years with no protection — shows dull, rough surfaces with deep holograms and UV damage in the clear coat. Here you need serious cutting volume to take off the damaged clear-coat layer and expose the intact material underneath. The Foam Pad hard is built for exactly this kind of work.\u003c\/p\u003e\n\n\u003cp\u003eOxidised paint — especially common on older cars or on plastic parts like bumpers — has lost the molecular structure of its surface to UV exposure. That dull, sometimes chalky surface only comes back with an aggressive pad and a cutting polish. The Foam Pad hard paired with PROFILINE CutMax is the recommended system for this job.\u003c\/p\u003e\n\n\u003cp\u003eGRP surfaces — boat hulls, motorbikes, caravans, sports vehicles — bring their own demands: GRP forgives overheating less than car paint but reacts much the same to mechanical abrasion. The Foam Pad hard is approved for GRP and gives good results on these surfaces as long as you keep the machine settings conservative (medium speed, light pressure).\u003c\/p\u003e\n\n\u003ch3\u003eThe Foam Pad hard compared — pad hardness grades in the PROFILINE system\u003c\/h3\u003e\n\n\u003cp\u003eIn the PROFILINE pad range the Foam Pad hard sits at the top for cutting power. By comparison: the \u003ca href=\"\/products\/sonax-profiline-schaumpad-medium-polierpad\"\u003eSONAX PROFILINE Foam Pad medium\u003c\/a\u003e is less hard and pairs medium cut with more gloss potential — it suits one-step polishes or mid-level defects. The \u003ca href=\"\/products\/sonax-profiline-schaumpad-weich-polierpad\"\u003eSONAX PROFILINE Foam Pad soft\u003c\/a\u003e is the pure finishing pad: very little cut, maximum gloss — only for finish polishes like PROFILINE NP \"03-06\" with no defects to remove first.\u003c\/p\u003e\n\n\u003cp\u003eChoosing between the hardness grades follows one simple rule: the heavier the defects, the harder the pad and the more aggressive the polish. If you run a three-stage process (step 1: remove deep scratches with hard + CutMax; step 2: remove holograms with medium + Cut+Finish; step 3: finalise with soft + NP), you get the best result. For simpler cases a two-stage process, or even a one-step pass with the medium pad, does the job.\u003c\/p\u003e\n\n\u003cp\u003eAlongside the Foam Pads, the PROFILINE system also has the \u003ca href=\"\/products\/sonax-profiline-exzenterpad-hart-polierpad\"\u003eSONAX PROFILINE Eccentric Pad hard\u003c\/a\u003e — a similarly hard pad, but specially matched to the motion of dual-action machines. If you work exclusively with dual-action machines, take a look at the Eccentric Pad hard; if you work with a rotary or several machine types, the Foam Pad hard keeps you flexible.\u003c\/p\u003e\n\n\u003ch3\u003eBuy the SONAX PROFILINE Foam Pad hard — sizes, system combo and recommendation\u003c\/h3\u003e\n\n\u003cp\u003eThe PROFILINE Foam Pad hard comes in two sizes: Ø75 mm for smaller backing plates and precise work on small panels, corners and bumper details — and Ø150 mm for large-area work on the bonnet, roof and sides. For a complete polishing station, go for a set of several pads in both sizes: that way you can swap between panels without waiting on a clean pad.\u003c\/p\u003e\n\n\u003cp\u003eThe ideal system combo for heavy defects: Foam Pad hard Ø150 mm + PROFILINE CutMax \"6\/4\" on a rotary or dual-action polisher for the first cutting pass. Then Foam Pad medium + PROFILINE Cut+Finish \"5\/5\" for the mid-level polish, and finally Foam Pad soft + PROFILINE NP \"03-06\" for the high-gloss finish. This three-stage product chain is fully covered in the PROFILINE range — every component is matched to the next and gives you repeatable results.\u003c\/p\u003e\n\n\u003cp\u003eFor detailing businesses it's worth keeping at least 4–6 Foam Pads hard per size on hand: that way you can always start with a fresh pad while used ones get freshened up during the overnight clean. The PROFILINE pad system pays off for shops with high vehicle throughput through its long service life and consistent cutting power, which keeps costly re-work from uneven results off your plate.\u003c\/p\u003e","brand":"SONAX","offers":[{"title":"Ø75 mm","offer_id":57345169654095,"sku":"D1-SNX-4921410","price":38.79,"currency_code":"USD","in_stock":true},{"title":"Ø5.9 inches","offer_id":57345169686863,"sku":"D1-SNX-4922410","price":15.64,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/sonax-profiline-schaumpad-hart_150-mm.png?v=1774736662","url":"https:\/\/detiiling1.com\/products\/sonax-profiline-schaumpad-hart-polierpad","provider":"Detailing1","version":"1.0","type":"link"}